HT/LT Cable Route GPR Survey in Ghaziabad

Rates and page checked: 23 October 2026

Which services does an electric cable route GPR survey in Ghaziabad look for?

Think of it as clearing a corridor on paper before a single shovel goes in: the planned cable has an alignment, and we establish what already occupies that band of ground. For an electric cable route GPR survey in Ghaziabad, we scan the full trench or bore line plus a working margin on each side, so the cabling contractor can shift the route where it is congested.

Along that strip we look for:

• existing HT feeders and LT distribution cables, old runs that may have been abandoned included;
• street-light circuits and earthing conductors;
• water supply lines, sewers and storm drains;
• telecom cables and fibre ducts;
• chambers, joint bays and old foundations that would block a trench or a drill head.

The output is ground marking in utility colours and a signed report listing each find with its position and approximate depth. This page deals only with power cable routes; the wider picture of survey work in the district is on our Ghaziabad GPR survey page, and the method in general is described under HT/LT cable route GPR survey.

Where do power cable routes in Ghaziabad run into congestion?

Some stretches are predictable trouble. When we plan a feeder survey here, these get closer line spacing from the start:

• Substation exits. Several outgoing circuits leave in parallel, often with older cables beside newer ones, and spacing between them can be tight.
• Township main roads. In high-rise areas each builder brought supply up to its own boundary, so footpaths can carry cables from several phases of development.
• Sahibabad industrial roads. Factory supplies, private HT connections and old process lines share the road edges.
• Corridor crossings. Where a cable has to pass the Delhi–Meerut Expressway or the RRTS alignment, the crossing is usually bored, and the bore path and both pits need scanning.
• Hindon crossings. Cables carried across the river by bridge or bore meet embankments and wetter ground near the approaches.

Knowing these spots in advance lets us price the extra passes into the quote rather than discovering them mid-route.

How is HT cable route mapping in Ghaziabad done on site?

1. Route check. We overlay the proposed alignment on the ground, note chambers, poles, feeder pillars and transformer locations, and agree the scan margin.
2. EM sweep. A locator is run in passive mode to pick up live cables, then with a signal applied wherever an access point allows, which is the most reliable form of underground electrical line tracing in Ghaziabad streets.
3. Radar lines. GPR passes run along the route with cross-lines at intervals and at every junction, catching plastic pipes and ducts the locator cannot sense.
4. Crossing passes. Each planned road, corridor or drain crossing is scanned on a closer grid across its full width.
5. Marking and report. Finds are painted or pegged on the surface, and the report records what was found, the depth reached on each section and any stretch we could not access.

Radar depth depends on soil and moisture. Wet clay cuts reach, dry sandy ground extends it, and the report says which applied where.

When should a Ghaziabad cable survey include an L-section?

An L-section survey adds a depth profile of the detected services along the cable route, charged at ₹32 a metre instead of ₹24. It is worth ordering when the work order asks for one, when a new cable must pass under or over existing services at known depths, or when a bore needs a clear vertical gap at each crossing.

It does not have to cover the whole route. Many contractors take the profile only at congested stretches and crossings, with standard scanning elsewhere. More detail is on our L-section GPR survey page.

What does a cable route survey in Ghaziabad cost?

Pricing follows the metre, with Delhi NCR terms: a 4 km minimum length and no per-project minimum. GST is charged on top.

A multi-feeder programme that passes 100 km in one order is discounted by 25% on every metre, rising to 40% past 500 km and 50% past 1,000 km. Mobilisation, night-shift work, traffic or permission arrangements and CAD/GIS drawing sets are quoted as separate items. See the price list for every slab.

Who orders power cable surveys in the PVVNL area?

PVVNL is the distribution company for Ghaziabad, and much of the cabling here is executed by contractors on its network or by developers building their own internal supply. Mezux Touch is not affiliated with PVVNL or any other DISCOM, municipal body or development authority; we act only for the client who places the order.

Our usual clients are EPC and cabling contractors, consultants preparing designs, and developers or plant owners laying private HT connections. As a power cable mapping company in Ghaziabad with owned radar and in-house crews, we can plan around a contractor's trenching sequence; see GPR survey for EPC contractors and our note on HT/LT cable mapping for NCR DISCOM work.