Skip to main content
ISO 9001:2015 · ISO 14001:2015 · ISO 45001:2018

GPR Survey — Ghaziabad

GPR Survey in Sahibabad, Ghaziabad – Underground Cable & Utility Detection

One of North India's oldest industrial areas, with rail sidings through it and a drain along the edge — and servicing that goes back further than most current occupants.

1.5 LAKH+ KMGPR Survey Completed
100 KM/DAYPeak Survey Output
700 KMFastest 30-Day Delivery
₹24/MStandard Rate · Min. order ₹50,000 NCR · ₹1,00,000 India

Owned radar only: more than 1.5 lakh km surveyed, a peak of 100 km in one day and 700 km inside a 30-day month. Sahibabad lies within Delhi NCR, so the minimum order here is ₹50,000 (covers up to 2 km), while the ₹1,00,000 minimum is reserved for sites outside NCR.

Quick AnswerMezux Touch runs GPR survey across the Sahibabad industrial area, the site sectors, the rail siding belt, the drain margin and the approaches toward Vasundhara and the Delhi border. Decades of industrial layering with almost no consolidated record define the work here.

Industrial servicing measured in decades

Sahibabad was industrialised long before most of NCR, and its subsurface reflects successive generations of manufacturing rather than a single planned installation.

Units that closed left their servicing in place. Plots were subdivided, re-let and repurposed. Power was reinforced repeatedly as loads changed, and effluent connections were made to whatever facility existed at the time.

The result is one of the most layered industrial subsurfaces we survey, and one where the phrase 'according to the drawing' carries very little weight.

Rail sidings, lifted and remembered

Several plots here were served by their own rail sidings when goods moved by rail. Most of those sidings were lifted decades ago, but the ballast, sleeper beds and the drainage that served them remain below the surface.

These return strongly on radar and must be distinguished from utilities rather than confused with them. Getting it wrong in either direction causes problems downstream, and it is interpretation work rather than an equipment question.

The drain margin and what happens beside it

Ground along the drain carries higher moisture, disturbed bedding and, in places, loss of material around buried services. Achievable radar depth drops noticeably within a belt inland from it.

Washout zones beside the drain turn up often; we list them apart from the utility plan because they describe a risk to a service, not where it lies.

Old effluent networks and current obligations

Trades that operated here historically ran effluent conveyance along routes that made sense for the plots of that era. Many of those plots no longer exist in the same form, and the routes cross what are now different boundaries.

Current occupants inherit the physical infrastructure along with the regulatory exposure, and probable effluent routes are flagged as their own category with their own confidence statement.

Ground conditions across the belt

This is trans-Yamuna alluvium with made ground of considerable depth across the older plots, higher clay content than the Noida side and moisture rising toward the drain.

Achievable depth is moderate rather than generous, and we state the figure by section instead of offering one number for the whole area. We calibrate as the ground changes rather than once at the start.

Files, and which office holds them

The industrial development authority governs estate land, the municipal corporation the surrounding roads, the railways their own land, and the irrigation department the drain margin.

None of them holds a complete picture, and assembling one means approaching several custodians rather than one. We identify which applies to each stretch before any application is drafted.

Related GPR services locally

For Sahibabad plots and roads we also carry out underground cable detection, underground pipeline detection and road and highway GPR survey.

Frequently asked questions

Because it was industrialised decades earlier. Units closed leaving servicing in place, plots were subdivided and re-let, and power and effluent connections were reworked repeatedly without consolidation.

Strongly. Ballast, sleeper beds and siding drainage remain below the surface long after the track was lifted, and distinguishing them from utilities is interpretation work rather than an equipment question.

Yes, within a belt inland from it. Higher moisture reduces achievable depth, and washout zones beside it are a recurring finding reported separately from the utility plan.

The current occupant generally inherits the physical infrastructure and the regulatory exposure with it, which is why probable effluent routes get their own reporting category and confidence statement.

Moderate rather than generous. Deep made ground, higher clay content and moisture toward the drain all reduce reach, so we state achievable depth by section rather than one figure for the area.

Only one minimum: any order is charged at least ₹50,000 (covers up to 2 km). Sahibabad is part of Delhi NCR, so the minimum order is ₹50,000 (covers up to 2 km); the ₹1,00,000 minimum is kept for distant sites.

On open corridors with round-the-clock shifts we have reached 100 km in a day, and 700 km in one 30-day month. Inside a Sahibabad estate the pace is far lower: fill, old sidings, factory gates and tight service clusters decide daily progress, and the programme says so.

Excavating on a Sahibabad plot?

Send the plot and what you know of its history — the servicing here usually predates whoever owns it now.

Get a Survey Quote+91 99100 10209

GPR survey in Sahibabad — deliverables, ground data and detailed questions

Survey work in Sahibabad runs through trans-Yamuna alluvium under deep industrial made ground, with buried siding formation and drain-margin moisture, so radar reach is more limited than in drier parts of NCR and is stated section by section in the report. That reach, more than the metres covered, decides whether the findings can support your design. When the dig must go below what radar can read, we say so before booking and suggest opening pits or drilling boreholes where it matters, on request.

How the survey is run here

Line spacing in Sahibabad follows the plot history and the fill, not a national template. Old ballast and rubble reflect strongly, so extra cross-lines are run there to keep false finds off the record. Velocity is reset each time the ground changes, letting depths along a mixed route be compared fairly. The crew and radar on site are always our own.

What you receive

Each detected line is marked on the ground and listed in a signed report with its approximate depth, the method that found it and a reliability grade. CAD drawings in DWG, or SHP/KML layers for a GIS, are separately quoted add-ons; the report is issued as a PDF. That report covers ground scanned, depth achieved per section, places we could not reach and any limits on the findings. On Sahibabad work the report also records the authorities involved — UPSIDA on estate land, Ghaziabad Nagar Nigam, the railways, the irrigation department near the drain — since any of them may ask to see the findings. Mezux Touch has no affiliation with these bodies. Raw radar files stay in our archive, which helps if a finding is disputed long after the works.

Beyond the basics

Why is Sahibabad harder than newer estates? It was industrialised decades earlier. Units closed leaving servicing in place, and plots were subdivided and re-let repeatedly.

Do old rail sidings show up? Strongly. Ballast and sleeper beds remain long after the track was lifted, and separating them from utilities is interpretation work.

Does the drain affect performance? Within a belt inland, yes. Higher moisture reduces depth, and washout zones beside it are a recurring separate finding.

Who is responsible for inherited effluent lines? The current occupant generally inherits the infrastructure and the regulatory exposure with it.

Can two contractors share one survey? On a shared corridor it often makes sense: one scan, one ₹50,000 minimum order and one mobilisation are split between them, and the report goes to both on terms agreed in advance.

Terms used on this page

Siding formation — ballast and sleeper bedding left in the ground after a rail siding was lifted. Washout zone — a pocket where flowing water has carried soil away from around a buried service. Regulatory exposure — liability for buried infrastructure inherited with a plot, regardless of who installed it. Achievable depth — the depth to which radar returns usable signal on a given stretch, often less than the equipment's rated figure. Unattributed find — a buried service no owner claims; it is reported as unknown instead of being credited to the likeliest owner.

GPR Survey — Sahibabad, Ghaziabad
Quick answer

As a GPR survey company in Sahibabad, Ghaziabad, Mezux Touch scans old industrial plots, estate roads and the rail and drain belts with its own radar and EM locators, finding cables, water and effluent lines before excavation. Crews come from Faridabad. Rates: ₹24 a metre, ₹32 with L-section, ₹50,000 minimum order in NCR; GST extra.

Rates and page checked:

Technician reviewing radar scan results on a tablet at the roadside
Readings are checked on site so doubtful returns on old plots get a second pass.
Diagram of a service route passing under a railway track
Former siding beds are logged separately so they are not mistaken for buried pipes.
Drawing of factory sheds on an estate with buried lines between plots
Decades of subdivided plots leave power and effluent lines crossing today's boundaries.
Printed survey report pages with a plan of detected services
The signed report lists each find with depth, method and a confidence grade.
How it works · Layering an old industrial plot
watergaspowerEACH LINE ON ITS OWN LAYER WITH DEPTH
  1. STEP 1Plot history collected
  2. STEP 2Radar grid and EM
  3. STEP 3Services sorted by type
  4. STEP 4Marks and report issued

What does a GPR survey company in Sahibabad, Ghaziabad get asked to scan?

Requests from this estate are shaped by its age. Almost every one involves ground that has been dug, filled and re-used several times, so the scan is planned around plot history rather than a clean road grid. Typical jobs are:

  • Power reinforcement for a unit. A factory taking a bigger load needs the route of its new cable checked from the supply point to the panel; our Ghaziabad HT/LT cable route survey page explains that job step by step.
  • Fibre into the estate. Operators bringing new duct to units along estate roads want room for the duct and clear bore paths, as set out under OFC route survey in Ghaziabad.
  • A full plot record. A buyer or tenant taking over an old plot may want every detectable line inside the boundary found and listed before redevelopment, which is utility mapping for Ghaziabad sites.
  • Pre-dig clearance for a shed extension, a machine base, a new sewer connection or road cutting on roads running toward Vasundhara or the Delhi border.

On most of these jobs, effluent runs and siding remains are recorded as their own categories, so the site team knows which finds are live services and which are leftovers.

How much does a Sahibabad survey cost under NCR rates?

Sahibabad sits inside Delhi NCR. That means one minimum only: ₹50,000 per order (covers up to 2 km). The ₹1,00,000 per-project figure that applies to outstation work is not used. For plot scans, the length billed is the total of radar lines run across the plot.

ExampleSurvey typeAmount before GST
Plot scan, 2.5 km of linesStandard₹60,000
5 km estate cable routeStandard₹1,20,000
5 km estate cable routeL-section₹1,60,000
110 km multi-estate programmeStandard, 25% slab₹19,80,000

The standard rate is ₹24 a metre; adding a depth profile makes it ₹32. Discounts grow with the whole order, reaching 40% beyond 500 km and 50% beyond 1,000 km. Anything outside the scan itself, namely mobilisation, night-shift work, traffic arrangements or permissions, and CAD/GIS drawing sets, is priced line by line and never folded into the metre rate. For each slab and a cost calculator, open the GPR survey price list.

Where can you read more before booking a Sahibabad scan?

This page deals with the Sahibabad estate itself. Other pages cover the wider picture:

If you are still unsure which survey suits your plot, send what you know of its past use and the planned work, and we will suggest the scope.

STEP 1

Share the plot history

Tell us what earlier units made on the plot, where old sheds stood and any drawings, however outdated, that still exist.

STEP 2

Fix the scan area

We agree the boundary, the frontage and any stretch beside the drain or a former siding that needs closer lines.

STEP 3

Radar and EM passes

Our crew runs a radar grid over the area and traces conductive lines with EM, adding passes over fill and ballast.

STEP 4

Sort what is found

Live services, probable effluent runs and siding remains are separated, so each category carries its own confidence note.

STEP 5

Mark and report

Finds are painted on the ground in utility colours, and the signed report follows with depths and access limits.

Insights

Sahibabad GPR survey in numbers

Rate per metre by order size

Standard vs L-section GPR survey, ₹ per metre

StandardL-Section
₹0₹20₹40₹60₹80₹24₹32Up to 100 km₹18₹24100+ km₹14.4₹19.2500+ km₹12₹161,000+ km

Source: Mezux rate card, October 2026.

Cost of longer orders

Standard ₹24/m with whole-order slab, ₹ lakh before GST

₹0 L₹30 L₹60 L₹90 L₹120 L₹24 L100 km₹18.2 L101 km₹90 L500 km₹72.1 L501 km

Source: Mezux rate card – amounts before GST.

Our recorded output

Route surveyed, km

0 km300 km600 km900 km1200 km100 kmPeak day700 kmFastest 30 days

Source: Mezux delivery records.

Fact table

FactValueSource
Crew and equipment baseSector 41, FaridabadMezux records
Standard GPR survey₹24 per metreMezux rate card
L-section GPR survey₹32 per metreMezux rate card
Minimum order inside NCR₹50,000 (covers up to 2 km)Mezux rate card
GPR survey completed by Mezux1.5 lakh+ km in 28+ States/UTsMezux records

Mezux Touch is not affiliated with UPSIDA, Ghaziabad Nagar Nigam, the railways or any DISCOM; drawings, mobilisation, night work and traffic arrangements are extra.

Best prices

Get GPR Survey in Sahibabad, Ghaziabad at Best Prices

One rate for old and new ground

Layered industrial plots cost the same ₹24 per metre as clean estate roads, even though they take longer to scan.

NCR minimum order ₹50,000

A Sahibabad order carries only the ₹50,000 NCR minimum (covers up to 2 km), never the ₹1,00,000 used for faraway sites.

Share a corridor survey

Two contractors working the same estate road can split one scan, one minimum and one mobilisation between them.

Pay for depth only where needed

Order the ₹32 L-section on stretches near effluent lines or crossings, and keep the rest on the standard rate.

Group several plots

Combine neighbouring units or a Ghaziabad road job into one order to fill the minimum with useful length.

Extras listed up front

Mobilisation from Faridabad, night shifts, permissions and CAD/GIS drawings are priced individually before the crew sets out.

Latest price list

GPR Survey Rates in Sahibabad, Ghaziabad – Current Rates

ServiceUp to 100 kmAbove 100 km
(25% off)
Above 500 km
(40% off)
Above 1,000 km
(50% off)
Standard GPR Survey
min. order ₹50,000 NCR · ₹1,00,000 India
₹24/m₹18/m₹14.40/m₹12/m
L-Section GPR Survey
min. order ₹50,000 NCR · ₹1,00,000 India
₹32/m₹24/m₹19.20/m₹16/m

Charged per running metre, before GST; the discount slab is decided by the total order and applies to all of it. Outside the Delhi NCR region the project minimum is ₹1,00,000. Mobilisation, night-shift working, traffic and permission arrangements and CAD/GIS drawing sets are quoted separately. Updated 23 October 2026.

Price range

Lowest rate₹12/mStandard, above 1,000 km
Highest rate₹32/mL-Section, up to 100 km
Minimum order₹50,000Delhi NCR (up to 2 km) · ₹1,00,000 Rest of India (up to 4 km)
FAQ

More questions about GPR survey in Sahibabad

Can you scan inside a working factory in Sahibabad?

Yes. We work under the unit's own permit and safety rules and plan passes around production, loading bays and shift changes. Areas blocked by machines or stock are recorded as no-access in the report, and we can return for them on a later visit if the layout changes.

Can radar follow a disused effluent line across a plot boundary?

Often it can, if the line is large enough and access exists on both sides of the boundary. We follow the line pass by pass and report where it was lost. Whether the line is still connected or carries flow is not something radar can tell, so we label it as a probable route.

Is Mezux Touch linked to UPSIDA or Ghaziabad Nagar Nigam?

No. We have no affiliation, approval or tie-up with UPSIDA, the Nagar Nigam, the railways or any power distribution company. Plot owners, contractors and consultants come to us directly, and our report records services of every owner we detect.

Can an L-section be ordered for part of a Sahibabad route only?

Yes. Many clients want a depth profile only near effluent lines, siding beds or road crossings. Those metres go at ₹32 and the rest at ₹24, with the ₹50,000 minimum order counted on the combined value of the order rather than on each type.

Will you arrange permission to work on railway or estate land?

Permission for railway land, estate roads or the drain margin rests with the bodies that control them, and the project owner normally applies. Our liaison staff can help with the paperwork. Any permission or traffic arrangement work is billed separately from the survey rate.

How is a single plot billed if it is far smaller than 2 km?

A plot scan is measured by the total length of radar lines run across it. Even a dense grid on a large plot rarely goes past 2 km, so it is usually charged the ₹50,000 minimum order. Adding neighbouring plots or an estate road job to the same order uses that length.

Get a quote

Send your Sahibabad plot or route

What to send for an exact quote

  • Route drawing, KML or list of roads with start and end points
  • City / district and site type (road, estate, plant)
  • Standard survey or L-section
  • Target start date and any working-hour limits
Standard GPR₹24/m
L-Section GPR₹32/m

₹24/m · Min. order ₹50,000 — Delhi NCR (up to 2 km) · Min. order ₹1,00,000 — Rest of India (up to 4 km) · GST extra · 25–50% off above 100 km.

What happens next

  1. Scope check – we confirm route length, crossings and L-section need.
  2. Written quote – rate, slab, minimums, extras and a day-by-day programme.
  3. Mobilisation – our own crew and systems on the agreed date.

Get a Quote

Route length, location and survey type – we reply with a written quote.

Trusted by India’s telecom & infrastructure leaders

Bharti Airtel
Tata Communications
TCIL
Reliance Jio
Gigatel Networks
RailTel
MTNL
BSNL
Vodafone Idea
P2P Networks
Bharti Airtel
Tata Communications
TCIL
Reliance Jio
Gigatel Networks
RailTel
MTNL
BSNL
Vodafone Idea
P2P Networks